How-To: Boxes from Recycled Greeting Cards

I promised months ago to post a tutorial on how to recycle greeting cards into tiny boxes, and finally managed to photograph one tonight while I was making it.

Before we get started, I have a couple of tips for box-making success. First, try to use a ruler that measures in sixteenths of an inch. You'll be able to measure more accurately. I don't have one, but I've made enough of these that I can estimate 1/16" fairly easily. Second, look for greeting cards that have a matte finish. For the box pictured here, I used a card with a glossy finish, and you can see cracks in the surface where I made the creases. A matte finish is less likely to do this, and will result in sharper edges and less cracking.

OK, first select a card and determine the largest size square you can cut from the front. You can go smaller than that if you like, but for your first box it's easiest to work as large as possible.

Next, on the reverse of your card front, draw your square, then place your ruler from corner to corner and draw an X in the center. This will mark the exact center of the square. On the back of the card (the blank area or the space where the greeting is), draw a square that is 3/16" smaller than your previous square. Mark the center.

Cut out the squares with scissors or a rotary cutter.



Beginning with the square you cut for the box top, fold all four corners to the center X and crease the folds.



Fold each straight edge toward the center, crease, and unfold.


Note the crease lines in the photo at left. It's important to complete all the folding steps above so that you make the correct cuts in the following step.



Using sharp scissors, cut from point A to point B. You'll be cutting through 2 layers of cardstock. Then cut from point C to point D. Repeat these cuts on the OPPOSITE edge of your folded card. IMPORTANT: You're only cutting on 2 sides, NOT 4.


Fold out the 2 sides you cut, as pictured at left.


Fold up sides 1 and 2 so that they're vertical.

Fold sides 3 and 4 over to hold sides 1 and 2 in place. If the little pointed sides don't stay down by themselves, glue them in place.

Repeat all steps for the box bottom. The top and bottom may fit very tightly together, depending on how carefully you cut and measured, or on your folding technique. Take this into account for your next box, and cut the box bottom smaller or larger accordingly. Be warned, these are addictive!

How-To: Fabric Gift Card Pouch

I sometimes feel like a gift card is a little bit impersonal, but so many people like to receive them, and they're so much easier to send long-distance, so I end up buying quite a few of them. Last night I was getting ready to put one in a card and send it off, when I came up with an idea to personalize it a little bit. The gift card pouch pictured here took only minutes to make, and I didn't have to buy any new materials for it.

I always have bits of fabric on hand that I've applied Wonder-Under to, just in case I want to do a project like this, so I was able to pull from that supply for my gift card pouch. In addition to the fused pieces, which are used for the outside, the lining, and the decorations, I used scraps of quilt batting (in this case, Warm & Natural).

First, cut 4 rectangles of my background fabric and 2 of batting, each sized 3-3/4" x 2-3/4". Set 2 of the fabric rectangles aside to be used for the lining. Fuse each of the other pieces of fabric to a piece of batting.

Cut your embellishments out of a contrasting fabric that already has Wonder-Under applied to the reverse side. In my case, I used a circle template to mark and cut circles in several sizes. Place those contrasting pieces onto your previously fused fabric/batting pieces and iron in place.

Using a decorative thread (I used Madeira rayon), embellish the surfaces as desired. Decide which embellished rectangle you want for the front of your pouch, and cut one end off at an angle. You could create a fancier edge, but I was trying to keep it simple. Zigzag that edge with decorative thread. This will be the top edge of the pouch front. If you want the edge to be completely smooth, you can use a satin stitch (a slightly rough edge doesn't bother me, so I just used a narrow zigzag).

Now fuse the 2 remaining fabric rectangles to the backs of your other pieces, completely covering the batting. You now have lined front and back pieces. Place one on top of the other, lining sides together, and zigzag or satin-stitch around the 4 raw edges. You're done!

In addition to the gift card, I was able to tuck a few other small goodies into my pouch. The next one I make will be about 1/4" bigger in both directions so I can use it for artist trading cards. The pouch pictured here almost worked for that purpose, but it was just a little too tight.

Artist Trading Cards - Wednesday Stamper/Two Tone

Now that I'm working 8 hours a day, I'm fiercely protective of my free time, and I don't always use that time efficiently because I'm spending too much of it deciding what I want to do. Tonight, I want to make ATCs, but I also want to finish a book I'm reading so I can stock up at the library again before the weekend. So I challenged myself to stamp something quick and easy, so that I'll have time left over for reading. The current topic at Wednesday Stamper is Two-Tone, and that helped me narrow down my color choices, which really did save time. For the second ATC, I used mostly scraps (have I mentioned that I never throw out even the smallest bits of leftover paper?). Now, I'm off to finish my book. Maybe I'll get done in time to do some more stamping!

Artist Trading Card - Games

I haven't posted an artist trading card in a while, so I thought I'd play along this week at Think Monday - Think ATC, where the current challenge is games. I honestly don't know why I have pieces of a child's jigsaw puzzle in my house (since all my children are of the 4-legged, furry variety), but somehow they've made their way into my stash of stuff and are therefore fair game for artwork. For this ATC, I roughly edged one puzzle piece with a Krylon leafing pen, and glued a crossword to another piece. The background paper is "Guy's Life" from American Traditional Designs. As always, the folks participating at TMTA have produced some fabulous ATCs, so head on over there and take a look.

Moo Card - Birds

If you love moo cards, you should head on over to Make a Moo or Two, where you can find loads of inspiration in dozens of styles. This week, the challenge topic there is birds. On the moo card pictured here, I've heat embossed a tiny bird in winter white, and simply layered her over some stamped flowers and swirls in cheerful summer colors. As I nearly always do, I've added a bit of knotted ribbon.

Moo Cards - Black and White

Finally, I had time to make some moo cards! I love to work small, and the moo card is probably my favorite format for little pieces of art. The nice thing about moos is that they can stand alone, or can be added to a greeting card or other piece of art. The cards pictured here are for Make a Moo or Two, where the challenge this week is black and white. Here, I've simply done some very basic stamping with black ink on white cardstock, then framed it all up on black cardstock. All stamps and cardstock are from Stampin' Up!.